Other

Hose Kits, Barbs and Strain Relief for Servicing Reverb Lines.

Remote rebuild kits and subcomponents for Reverb and Reverb Stealth Posts.

RockShox Reverb/Reverb Stealth IFP - Fits Reverb and Reverb Stealth

Service kit to assist in scheduled maintenance and/or rebuild of RockShox dropper seatposts.

- Yari Solo Air A1 1 year service kit - Includes dust seals, foam rings, o-ring seals, SA sealhead

Eliminate dropped chains forever with the new OneUp Components Bash Guide. As the trend for lower and slacker bikes continues, chainring protection is becoming even more important. Revised for 2019 the OneUp Bash Guide uses simple, one tool installation and adjustment as well as an all new tool less flip The OneUp Bash Guide was developed with input from top EWS World racers and can be seen all over this years circuit. Reinforced Nylon bash guards and a back plate cut from 8mm thick 7075-T6 aluminum, ensure that the OneUp Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you may forget it’s even there. NOT JUST FOR ENDURO RACERS. The OneUp Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers and Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention. The OneUp Bash Guide includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 90g 28-30T, 105g 32-34T, 110g 36T - Capacity: 28-36T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic

This kit includes all the parts required to rebuild your V1 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V1 Dropper Post ONLY. We have found that ~95% of posts with slow top out were caused by low air pressure. Please make sure to check this first and do so with the post fully extended. Proper air pressure is 280-300psi at full extension, and the valve is located under the top clamp. If you are still having slow top out then there is a possibility that the upper white bushing needs replacement. This will be evident by the original bushing being difficult to reinstall after being removed.

This kit includes all the parts required to rebuild your V2 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V2 Dropper Post ONLY.

Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with Shimano I-Spec EV (M9100, M8100, M7100) brake mounts. - Does not contain remote body.

Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with SRAM MatchMakerX (MMX) or Shimano I-Spec EV (M9100) brake mounts. - Does not contain remote body.

Set of six oversized pins. All dropper posts require key way clearance. With so many different frames, clamps and ride heights it's not possible to ship play-free without running the risk of binding. The kit is meant to remove additional play that might develop over time or, for the more mechanically inclined, to tune the play out for a specific bike. Start with the 3 pins marked with 2 lines. If play still exists move to the 3 pins marked with 4 lines.

Eliminate dropped chains forever and add a touch of colour to your e-bike with the new OneUp Components STEPS Chain Guide. Available in 7 colours. The OneUp STEPS Chain Guide is lightweight and incredibly easy to install and use. The top guide has a tool-free flip feature that allows easy access to your chain for cleaning and maintenance. Top guide pieces are available in 6 bright colours to perfectly match your OneUp Composite Pedals, Grips and EDC Lite. Compatible with 32T to 38T chainrings. Weighs just 45g. FEATURES - Shimano STEPS E7000, E8000 and EP8 compatible - Includes black top guide piece. 6 other colours sold separately - Tool-less upper guide flip - Install without removing your cranks - Mounts directly to motor - Single tool install and adjustment (4mm hex) - Black Stainless-Steel hardware - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 45g - Capacity: 32-38T - Chainline: 5mm adjustment - Mount: Shimano STEPS/EP8 - Colour: Black top guide piece included. Blue, Green, Orange, Purple, Red, Turquoise sold separately. - Material: Back Plate - 7075 aluminum, Top Guide - glass reinforced thermoplastic

The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8" aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. KIT INCLUDES - EDC TOP CAP - EDC steerer plug - 2x 1mm, 3mm, & 5mm Headset Spacers

If you're not looking for chain retention or your bike has an integrated chain guide, you can still add some bash protection with the OneUp ISCG05 Underbash. The Underbash includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. Designed for frames with 2 ISCG05 tabs only (Evil, Rocky Mountain, etc). If your bike has three ISCG05 tabs, check with the frame manufacturer to ensure the lower tabs are strong enough for a bash application. Failure to do so could result in frame damage. FEATURES - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) SPECS - Weight: 68g 32-34T - Capacity: 28-36T - Chainline: 2.5mm adjustment - Mount: ISCG05 2-Bolt ONLY - Color: Black - Material: 7075 aluminum, glass reinforced thermoplastic

SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with both Shimano Hypergilde+ 12 speed chains and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - 3 Offsets - Regular, Boost and Super Boost - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 69g (30T Boost Cinch Oval) - Chainline: Regular (49mm), Boost (52mm), Super Boost (56.5mm) - Compatibility: Race Face Cinch cranks; 9, 10, 11 and 12 Speed Chains

SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with both Shimano Hypergilde+ 12 speed chains and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - 3 Offsets - Regular, Boost and Super Boost - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 66g (30T Boost Oval) Chainline: - 6mm offset - 49mm GXP/BB30 Long Spindle - 3mm offset - 52mm (Boost) GXP/BB30 Long Spindle - 0mm/SB - 49mm BB30 Short spindle, 56mm GXP/BB30 Long Spindle Compatibility: SRAM DM cranks; 9, 10, 11 and 12 Speed Chains

SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with all 8, 9, 10, 11, and both Shimano Hypergilde+ 12 and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 69g (30T Oval) - Chainline: Standard is controlled by the crank. - Compatibility: Shimano direct mount XTR M9100, XT M8100, SLX M7100 series cranks. - Color: Black

Replacement idler and idler kits for high-pivot Norco Range mountain bikes. Fits: 2021+ Norco Range Specifications: Size: 18T Narrow/wide tooth profile Machined from solid 7075 T6 Aluminum Anodized pewter with laser etched graphics Idler kit includes Enduro 6902 LLB ABEC-3 bearing and retaining clip Model: NSB IP0010

Replacement idler and idler pulley kits for high-pivot Norco Shore bikes. Fits: 2021+ Norco Shore Specifications: Size: 16T Narrow/wide tooth profile Alloy option machined from solid 7075 T6 Aluminum Anodized pewter with laser etched graphics Steel option machined from 4140 Steel Nitrox coated with laser etched graphics Idler kit includes Enduro 6902 LLB ABEC-3 bearing and retaining clip Model: NSB IP0005

The Sight Carbon F29"/R29" Missing Link kit allows you to convert your bike to a 29"wheelsize configuration without any compromise to geometry, kinematic or shock tune. The Missing Link kit includes a linkarm and two lower shock mounts, which must be installed as a kit. For installation, please refer to the assembly instructions.

18 tooth Aluminum Idler Pully 52mm CL Sold individually 2021+ Range HP

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - Indexed shifter adjustment, fits 4.0mm housing; not recommended for use with brake systems - Compact design improves performance when used on curved housing segments

- Mega Exo right hand threaded (RH) hollow carbon screws with a self-extracting cap - Designed to fit FSA MegaExo Cranks only - Includes bolt, self-extracting cap, and washers

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Star Ratchet Kit - 36T

- Simple tension seeker (STS) allows the use of a 1 speed drivetrain on a vertical drop frame - Perfect for street or dirt jump where simplicity and durability is key - Stainless steel arm mounts to derailleur hanger and dropout - Loosen bolt and swing down and back to adjust chain tension - High density polyurethane pulley with sealed cartridge bearings

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Lightweight aluminum construction

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 30mm (1-1/8") straight steerer tubes - Durable steel construction - Allows the installation of a straight steerer fork without changing out the headset lower

Installation of air volume reducers for Cane Creek shocks make the spring rate more progressive. - Spacers can be cut to fine-tune spring curve